Zeige alle Beiträge eines Teilnehmers

Re: Wurlitzer Niagara - 11 Jahre - Years

Hi I have replaced ic 16, fairly difficult to replace these surface mounted chips, and thankfully now the unit works correctly, thank you for all your advice and effort regards seancalla

von - by seancalla - Alles rund um Musikboxen

rockola 432 - 11 Jahre - Years

Hi i have inherited a rockola 432, and i just want to check the location and colour code of wires on the three microswitches at the cam shaft, not sure if the previous owner had them wired up correctly, as the tone arm cut of switch will not work ,and if you manually bring the gripper arm back when turned off ,it will cycle into the same position when you turn it on again regards seancalla

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 11 Jahre - Years

Hi Should have said its the older unit with ic16, will replace ic16 and let you know how i get on thanks seancalla

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 11 Jahre - Years

Hi Its the unit with ic22, i checked pin7 when the gripper is at rest and it reads 4.9 volts, i then checked the optocoupler bridging pins 4 and 5 and it started the record carrier and it selected a record For R49 it reads 1900 ohms, it is a large resistor, no breaks or burn marks For R44 read ok for resistance, no breaks or burn marks For D13 i checked continuity in circuit and reads 700 one

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 11 Jahre - Years

Hi After making a selection I checked pin 16 on ic 8, zero volts, replaced the chip with the same result of zero volts Checked R45, resistance is ok but no voltage I jumpered the outer pins at T4 and the relay operated and carrier moved, the carrier will also move if I manually press the relay, Regarding D9, no voltage was present when machine was switched on, i checked continuity in both di

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 11 Jahre - Years

Hi I'll give that a try, might take a day or so, do you know the exact spec of T4, may as well get one just in case regards seancalla

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 11 Jahre - Years

Hi Haven't received the ic's yet, but i have another problem with a similar machine, where the selection does not work, this particular machine will accept credit, will accept the input of numbers which are displayed, but will not initiate selection, z and k lights are ok, input voltages are ok, manually when you press relay m3 it will move the record carrier as well as using the hand

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi the socketed ic's at 7,8 and 11 are very confined and difficult to take out on this pcb, anyway have removed them and reseated ic11, but I will wait until i get replacement ic's for 7 and 8 and test the unit then, i will update you on my progress, they didn't arrive in the post today so it will be Monday regards Seancalla

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi what it did and hasn't done since was it selected over different selections over the course of five minutes. The voltage regulator measures 5 volts. I lifted out the PIA and there are slight heat/burn marks on the chip socket, i have ordered one along with a replacement for ic7 where there are burn marks also. As a matter of interest where could a replacement ROM be sourced from and whic

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi I replace C7, no change with the display or no selection possible. Something odd happened after i switched it off and on later on, the gripper arm for about 5 minutes started to select records place them on the turntable and immediately return them, stopped after about 5 minutes and didn't happen since even when i turned it off and on a few times, tried today and issue with the gripper

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi will replace C7 shortly, currently the magazine will rotate when operated manually ( i assume it is the lever beside the light gate), the light gate lights up,the z and k led's are normal as is the m led when i press to add credit on the credit board, will post an update on the capacitor in a while regards seancalla

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi thanks for the assistance,i checked the blue connector and it works ok, i get voltage(30) when it is at its rest position and 0 volts when the gripper arm is tripped into position. Not sure about checking shorts or open on capacitors but here's what i did, i firstly tried continuity on C22 with the red lead on the positive and the black lead on the negative of the capacitor and the mete

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi I have attached a number of photos of the scc, i measured 39.5 v dc at C7, 12.5 v dc at C4 and 13.5 at C22, in the manual it refers to 5 volts at pin 40 on ic 7 and i measured about 4.9. Diode 2 measures 5 volts, at the yellow plug the key and reset inputs measure 4.9 and fall to zero when pressed and just to recap i measured 30, 12 and 12 at the blue lug, and 40 volts at wire to indicator

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara - 12 Jahre - Years

Hi just an update on this with regard to my initial post, i by mistake was measuring dc volts on the red plug attached to the scc, i have measured with ac volts and they all read correctlt(30,12,0 and 12 volts) so please disregard my request on the source of a transformer under the chassis, but it still leaves the scc unable to select, there is no display under either credits or record number. I

von - by seancalla - Alles rund um Musikboxen

Wurlitzer Niagara - 12 Jahre - Years

Hi I am trying to repair the Wurlitzer Niagara jukebox but i am having the dreaded selection problem with no digits or credit in the display and no selections possible, the scc seems slightly different from other scc's that i have come across, i don't see a battery in it. I measured voltages at the keyboard input(yellow plug) which are 4.9 volts.I measured voltage at the red plug and

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara 5 - 12 Jahre - Years

Hi I tightened the very small hex bolt on the tone arm shaft blow the chassis and that seems to have put it right,thanks seancalla(will update at a later date on the wurlitzer caravelle)

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Niagara 5 - 12 Jahre - Years

Hi the tone arm seems to be mounted firmly, and the sequence of operations seems fine, its a an unusual problem, sometimes i can get it to lift off and land correctly when i firstly apply some pressure to the tone arm post maybe the whole thing needs to be dismantled and reassembled, re the caravelle that fix is on hold until i source some ic's thanks seancalla

von - by seancalla - Alles rund um Musikboxen

Wurlitzer Niagara 5 - 12 Jahre - Years

Hi I have one of these machines with a slight tone arm problem. Firstly I'll give a bit of background, from my previous experience with these series of jukeboxes, the rest position of the tone arm is just above the outer edge of the turntable. When you select a record the tone arm moves to just beyond the needle brush , after the record is placed on the turntable the tone arm advances to th

von - by seancalla - Alles rund um Musikboxen

wurlitzer caravelle - 12 Jahre - Years

Hi have come across one of these machines in good cosmetic condition, however the selection appears to be faulty, it will accept credits but wont register any selections, the selction or (computer) is a 40340, i only had limited time to look at it but is this a common problem with them, are there any fuses or batteries located on the pcb or would anyone know what i would need to look for and wou

von - by seancalla - Alles rund um Musikboxen

Re: nsm consulette E - 12 Jahre - Years

hi got it worked out, in line F a diode sits at points 5 and 8, and in line E a diode sits at point 8, thanks for the help

von - by seancalla - Alles rund um Musikboxen

Re: nsm consulette E - 12 Jahre - Years

Hi thanks for the information,do you know what is the positions for all of the other diodes, for example with diode at position E 8 where it lets selection from 1 up to 7 but not 8, i see that moving this one in the E row results in blocking off other numbers,(the only one in that row) it can vary from blocking off from 3 to 8 , there are two diodes in row F, should there only be one, tried a nu

von - by seancalla - Alles rund um Musikboxen

nsm consulette E - 12 Jahre - Years

Hi I am setting up this wallbox with an nsm city 2, the nsm city 2 records run from 100 to 179, the wall box numbers run from 10A to 89A. When set up the wall box will select the first forty records in the nsm city using the numbering system 10A to 49A on the wallbox, the first forty records are selected correctly including B sides, however the next forty records can't be selected if you en

von - by seancalla - Alles rund um Musikboxen

Re: NSM Prestige II ESII - 12 Jahre - Years

Hi If its any help might be a longshot, i had a similar with an nsm city 2 jukebox where the carriage was stuck and constantly spinning even if you moved the tonearm to the end or pressed reject, and it also made a humming noise, what was wrong in my case was that the tonearm was stuck between where it should be for an A side and B side, i moved the tonearm to the side manually where it should b

von - by seancalla - Alles rund um Musikboxen

Re: NSM performer grand - 12 Jahre - Years

thanks for that

von - by seancalla - Alles rund um Musikboxen

NSM performer grand - 12 Jahre - Years

Hi i have a nearly working performer grand, however on the left side between numbers 1 and 50 some of the trays are not taken out by the gripper and hence you get an error 71, always the same trays, six in total, all of the other trays will select no problem, anyone any ideas, regards seancalla

von - by seancalla - Alles rund um Musikboxen

Re: NSM Performer Grand - 12 Jahre - Years

problem sorted

von - by seancalla - Alles rund um Musikboxen

Re: NSM Performer Grand - 12 Jahre - Years

anyone any ideas about this will a new cd unit sort out the error 60 problem or is there any particular problems with power supply connections to the cd unit seancalla

von - by seancalla - Alles rund um Musikboxen

NSM Performer Grand - 12 Jahre - Years

Hi I have since solved the error 74 problem, but now initially I had an error 61, it would take the disc and spin a little and return it but now I have an error 60 the gripper takes the disc brings it to the cd player, it doesn't spin and then returns it, all connections are in place and all fuses ok, the manual refers to a primary fuse at the cd transformer, is this one of the fuses on th

von - by seancalla - Alles rund um Musikboxen

NSM Performer Grand - 12 Jahre - Years

Hi Have this jukebox which when turned on shows an error 74, have looked at the error code list which states causes as error during replacement of right side magazine,malfunction grip lever and possible corrections - check alignment to pick up assay and adjust if needed, check function of grip, check function of light barrier OPGRL. Could anyone explain what the error means and what someone woul

von - by seancalla - Alles rund um Musikboxen

Re: Wurlitzer Baltic 100 - 12 Jahre - Years

After a bit of investigation, i fould that the blade on microswitch K1 had slipped slightly of the cam, once adjusted back into place the records are now being slected and played, just need to do some adjustments with the tonearm as it is starting into the song about a third of the way through, anyone any ideas on troubleshooting the keyboard latch to reset the keys seancalla

von - by seancalla - Alles rund um Musikboxen