Zeige alle Beiträge eines Teilnehmers
Solution,
Computer was broken, replaced and works now.
Regards nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hello all .
I have an NSM Prestige ES 160 with a 200watt central unit/amplifier.
Everything in the central has been renewed and everything works fine, but there is still a problem.
as follows,
turn on the jukebox.
make a selection and pick up the record and start playing.
now the sound of the first record is distorted for at least 30 seconds and then comes on and the sound is ( only the f
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hi to all ,
I am working on my prestige es 160 .
Recap all capisitors in de central unit and all pcb units preamps etc.
Replaced 2 powertransitors bdw83c and bdw84c .
So now all leds are on and voltages are there when i turn on the jukebox.
The only thing not starting up is de computer and no display.
I checkt all voltages on the molex connector to the computer and they are al
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hello stig,
As Jurgen indicates can be the case , I have seen it done and you can easily enlarge the motor shafts to test this, namely, take a shrink sleeve of the right diameter and slide it over the motor shaft (s) then heat it slightly until it has shrunk firmly.
If it does run at the right speed, then you can choose whether you want to leave it that way. Or you want to change it .
rega
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hi stig ,
I am not familiar with the es2 system, but I have an E120 hit myself and the service manual says something about 50hz and 60hz.
This hit E120 can be usa connected to 117 volts on the transformer that is at the bottom of my cabinet, the 220v 50hz can also be connected.
Maybe there is information about that in the service manual?.
You may be able to check something else.
Turn
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hello to all .
I am working on a 50M amplifier and the mpf970 is defective.
Now I have found and ordered a replacement j-fet J174.
meanwhile it arrived.
Now I can find the pinout of the j174, but not of the mpf970.
Can the j174 be replaced directly 1 on 1? .
If I saw correctly, the source drain and gate is different, namely j174 pin 1 = drain pin 2 = gate and pin3 is source .
The
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hello stig.B
and jurgen .
I have an E120 model and the record carts are similar.
Maybe u can do this ,
To start with, thoroughly clean the motor that moves the mechanism including the motor shafts, which means removing the entire motor (s)
This is a patient job and you will need the service manual if you have not already done this, because there are 4 different rings including a retaini
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hallo josef,
Google hat meine Texte übersetzt, also entschuldigen Sie eventuelle Fehler.
Allerdings wird Jens am nächsten sein, er weiß auch fast alles.
Ich hoffe du kommst mit deinem Problem weiter.
Ich schaue und lese mit und bin wirklich gespannt, ob Sie die Lösung finden werden.
grüße nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hallo Josef .Jens,
Ich hatte auch dieses Problem mit Unterdrehzahl. (Meine Jukebox war die Hit E120, mit dem gleichen System glaube ich)
Nur das war nach Erneuerung der 2 grünen Folienkondensatoren 10uf 160 Volt, für gewöhnliche Elkos.
In der Einheit mit Kunststoffabdeckung, an der die Lautsprecher etc. angeschlossen werden.
Hast du es zufällig getauscht?
Gruß Nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hallo bob ,
Haben Sie dieses Prestige E160 schon lange und konnte es jemals 80 Auswahlen treffen? .
grüße nico.
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Haben Sie Fortschritte bei der Suche nach den Fehlern gemacht?
Gruß Nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hallo Patrick,
vergewissern Sie sich, dass Sie ein Servicehandbuch haben, und schauen Sie sich dann die Bedienung der Jukebox an.
da dieses Problem wirklich verschiedene Lösungen hat.
Ich kann dir einen Tipp geben, sprich das Auto von gummiertem Fett zu befreien und zu schmieren.
schau dir mal die stifte in der stiftbank an, diese sind oft mit altem fett verklebt oder zu trocken.
Suchen
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Es gibt auch ein Relais in der Steuereinheit, um den Motor zu steuern.
Links und rechts vom Plattenladen sind Mikroschalter und diese kann man messen, ob sie funktionieren, sie bestimmen, wann das Auto die Richtung ändert.
Die Kontaktzungen direkt unter dem Widerstand rechts neben dem Magazin können ebenfalls falsch ausgerichtet sein.
Es ist in der Tat nützlich, einen Schaltplan oder ein Han
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hallo
Ersetzen Sie auf jeden Fall den Kondensator (4uf nicht mehr oder weniger.
.
Spannung 250V mag.
Messen Sie auch den daran angebrachten Widerstand über den Schaltermessern.
Sehen Sie, ob der daran befestigte Schlitten einen guten Kontakt hat.
Der volle Widerstand sollte 400 Ohm betragen.
Und von unten bis zum Schlitten am Widerstand habe ich 270 Ohm gemessen und mit mir gearbeitet.
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hi ,
i can give u advice to get a service manual first , and clean the mechanical parts first , and do the grease en oil plan .
then u can see what the machine does and not .
good luck and regards .........nico
and indeed check the fuses first .
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Kai,
wenn sie nach guten Informationen suchen, ist jens der mann, der ihnen helfen kann. Dieser hat mir auch schon oft mit sehr genauen Informationen und Tipps weitergeholfen.
Es gibt bereits einige Themen, die Sie lesen können, wenn Sie möchten.
grüße nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hallo Kai,
Google übersetzt, also entschuldigen Sie die Sprachfehler.
Wie ich bereits erwähnt habe, könnten die zusätzlichen Kontakte an der Rolle und die Relais im Kontrollzentrum eine Modifikation als Vorlauf auf einem Stepper sein.
Achten Sie beim Austausch des Plattenwagens zwischen den 2 Musikboxen darauf, dass der Widerstand über den Schaltkontakten an beiden Musikboxen anliegt, sonst fu
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
jens ,
According to roy kroesen a friend of mine , this is probably a modification for one of the first steppers for a wallbox on 130 models
regards nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
the only difference i can see is , the 2 relays are mounted sideways instead of frond down .
So its the correct one for the 130 i think , the 130D has extra PCB print on the left and right side and wont work on a 130 .
Normal the relays are mounted all side down in most cases .
But this is not the standard unit for the 130 stereo magic .
greets nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hello all
In order not to let this rabbit hole to go on indefinitely, I have done the following.
I have disconnected the fluorescent tubes and then the hum has disappeared , and that is a good thing.
Now I have wrapped the LED strip around the fluorescent tubes as a solution and the light brightness is the same as the fluorescent tubes without interference.
Adapter driver for the LED
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Thank you for your clear explanation, I can't add anything to it nicely explained.
Nice pictures as an example thank you for that !
What I have now tried is turning on the jukebox and turning the fluorescent tubes a quarter of a turn so that they are off.
It was surprising that the malfunction had almost disappeared .
be continued
regards nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hi sven \ Jürgen,
At first the grid i made was to big because the TL hit the grid , so after a little tweaking i got it right in dimensions .
The hum was slightly less than without the grid
The grid creates a shadow on the top window so i need to reconfigure the grid that is not easy because there is really no room to work with .
And Jürgen indeed the cables from the amplifie
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
Hi sven i made a cage from perforated steel plate with ground point en tomorrow i wil see if this version will work , or i have to make one from sheet aluminium with vent holes
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hi sven ,
indeed your right , i opened the lid and the hum was almost gone , so thanks i now know where take on this problem .
ill let u know when am done and te results .
regards nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
oke sven .
So u think it the TL that causses the interference on the amplifiers .
the top TL tube is already led Tube .
So your option is to build a aluminium shield over de amplifiers .
Maybe its better to remove the ballast on de TL Unit and make it all led Tubes , without the old ballast and TL tubes .
At first i will take your info and make a shield , if that does not give the
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
thanks sven i wil try to get a netz filter en place it on the mains input .
i wil let u know if that works .
regards , nico
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen
hello jukebox fellow friends.
I have an nsm hit 120E electronic .
The amplifiers and the unit that is coupled to them have all been fitted with new capacitors.
The point here is that when the shure cartridge is not connected and the jukebox is only on, a small hum can be heard through the speakers. ( with carriage en shure same hum no differents )
So it's not a problem with the carri
von - by
n.vandebroek@hetnet.nl
-
Alles rund um Musikboxen